Owens Corning
Architectural shingles
Metal roofing
Tile roofing
GAF
Flat & low-slopeFree roof inspection with deck photos before we talk money - GAF and Owens Corning certified installation
Owens Corning Ridge Vent Installation: The Sunrise Manor Owner’s Guide
We install Owens Corning-compatible ridge vent systems across Sunrise Manor, and most single-ridge replacements land between $420 and $850 installed, depending on roof pitch, ridge length, and whether the underlayment beneath the vent has aged out. Ridge vent work is usually scheduled within a few business days, not months. Owners typically discover the failure the same way: a dark stain spreads across a ceiling in a back bedroom after a monsoon, or the attic hits 140 degrees by noon in July and the second-floor air conditioner never catches up. When you climb up to look, the vent ridge is cracked, the filter material is packed with dust, or the nails have backed out and the whole strip is lifting. That is the moment to call us at (844) 941-3509.

Which Owens Corning Models This Applies To
Owens Corning sells ridge vent under the VentSure brand, and the two products most Sunrise Manor homeowners are dealing with are the Rigid Strip and the Xtractor. Rigid Strip is the classic 4-foot sectional vent that comes in 12-inch, 9-inch, and 7-inch widths to match common ridge cap profiles; the roll version (VentSure Roll) is 20 feet and often used on longer ridges and lower-slope roofs. The Xtractor is the taller, more aggressively baffled design often specified for hotter climates where attic ventilation volume matters more. Knowing which one you have matters, because the shingle-over flange width and the shingle cap that goes on top have to match.
The fastest way to identify yours is to measure the flat width of the vent flange on either side of the ridge, then look for the profile name stamped on the underside of the plastic. If the label is gone (common after a decade in Nevada sun), photos from the ridge line and a measurement are enough for us to match it. On OEM versus aftermarket: for VentSure Rigid Strip, quality aftermarket vent strips from GAF or CertainTeed are dimensionally compatible and hold up well, and we will tell you honestly when that is the smarter call. For a direct VentSure Xtractor replacement where a specific baffle profile was specified, staying with the Owens Corning part keeps the airflow rating intact. We install Owens Corning products as an authorized installer, but we are an independent contractor and not affiliated with Owens Corning.
Styles & brands we work with
- Architectural shingles
- Metal roofing
- Tile roofing
- GAF
- Owens Corning
- Flat & low-slope
Signs Your Owens Corning Ridge Vent Installation Is Failing
Ridge vents do not announce themselves. They fail quietly, and the signs show up somewhere else in the house. Here is what we look for on Sunrise Manor roofs and what each symptom tells us.
- Ceiling stains or damp attic sheathing after a storm. The vent flange has lifted or the nails have backed out, letting wind-driven rain slip under the shingle cap and into the deck. In Sunrise Manor, the late-summer monsoon drives rain sideways, which finds even a small lifted edge.
- Attic temperatures climbing past 130 degrees in July. The filter material inside the vent (the fibrous mat that keeps out dust and insects) has clogged solid, choking off airflow. Nevada’s dust load accelerates this; a vent that breathes fine in a wetter climate can clog inside eight to ten years here.
- Ridge cap shingles curling, cracking, or blowing off. The vent shingle-cap pattern was installed too tightly, or the vent underneath has warped, and the caps no longer lie flat. Once they lift, the next wind event peels the whole ridge.
- Visible cracks or sun-chalked plastic at the ridge. UV exposure is brutal on the plastic body of the vent. We regularly see VentSure strips in Sunrise Manor that have gone brittle and cracked at the fastener holes within 12 to 15 years, well before the shingles around them gave out.
- Ice damming in winter, or condensation dripping in the attic. A blocked or undersized ridge vent no longer exhausts warm, moist attic air. In the cool months that moisture condenses on the underside of the roof deck and drips, which is a venting problem, not a roof leak.
See the difference
Before
After
Before
After
Before
AfterReplacement Cost & What’s Included
Ridge vent replacement is priced by the linear foot for the vent itself plus labor to remove the old strip, inspect the deck and underlayment, and re-cap the ridge. For a typical Sunrise Manor single-family home:
- Owens Corning VentSure Rigid Strip, standard replacement: $420 to $850 installed, covering one ridge run of roughly 20 to 40 feet.
- Longer ridge runs or Xtractor profile: $900 to $1,600 installed.
- Add-on if the underlayment or deck is soft: $8 to $14 per linear foot for new underlayment; deck repair quoted separately after inspection.
What drives the range: ridge length, roof pitch (steeper roofs take longer and more safety setup), whether the vent is the sectional Rigid Strip or a roll, and how much of the shingle cap needs replacing. The quote is line-item, and the number on the estimate is the number on the invoice. The work is covered by our 90-Day Done Right Promise: if it is not right, we come back and make it right, no arguing.

DIY or Call Us?
There is a safe version of owner involvement and an unsafe one. The safe part: from the ground or a window, look for lifted ridge caps, stains on the ceiling, and attic heat that never drops. If you can safely reach the attic, check that the vent slots cut in the deck actually align under the vent strip (a common install shortcut). That is inspection, not repair.
Here is where DIY goes wrong. A ridge is the highest, most exposed line on the roof, and replacing a ridge vent means pulling shingle caps, working on a steep slope, and reinstalling a shingle-over vent so it is watertight. Fall risk on a two-story Sunrise Manor home is real, and a vent that is not lapped and nailed correctly lets water in during the very storm you installed it to survive. We would rather you call and get it done once. Our technicians are background-checked and uniformed, have up to 10 years of experience, and have installed thousands of ridge feet across the valley. Call (844) 941-3509 for a free estimate.
FAQs
Expect 12 to 18 years before the plastic body and filter degrade in Nevada’s sun and dust, though the shingle caps over it may last longer. UV exposure here is the main reason VentSure strips in Sunrise Manor fail before the roof itself does, and the filter mat often clogs years before the plastic cracks. Call (844) 941-3509 for a free inspection and an honest read on how much life your vent has left.
Sometimes, yes: if the vent body is sound and only the shingle caps or fasteners have failed, we can re-cap and re-secure it, usually for $180 to $400. If the plastic is cracked or the filter is packed, replacement is the only honest fix, and we will tell you which you are looking at. Call (844) 941-3509 for a free estimate and a straight answer.
A standard single-ridge replacement is a few hours, and most of our jobs are completed in a single visit. Longer ridges or Xtractor profiles with deck repair can take a full day, and we tell you the schedule up front. Call (844) 941-3509 to schedule a free estimate.
We install Owens Corning products as an authorized installer, so we source VentSure Rigid Strip, Roll, and Xtractor through approved supply channels and verify the profile and flange width before it goes on your roof. We do not claim to keep parts on hand or stocked locally; we order to your measured ridge specification. If your roof calls for a compatible aftermarket strip instead, we will show you both options with pricing side by side. Call (844) 941-3509 to start with a free estimate.
When your ridge vent needs replacing, the goal is simple: get it done once, on the right profile, and never think about it again. Ridgeline Roofing Co. Sunrise Manor installs Owens Corning-compatible ridge vents with no-hassle upfront pricing, background-checked technicians, and the 90-Day Done Right Promise behind every job. Call (844) 941-3509 today for your free estimate.
Written by the team at Ridgeline Roofing Co. Sunrise Manor, serving Sunrise Manor and nearby areas.