Architectural shingles
Metal roofing
Tile roofing
GAF
Owens Corning
Flat & low-slopeFree roof inspection with deck photos before we talk money - GAF and Owens Corning certified installation
CertainTeed Flashing Replacement: The Sunrise Manor Owner’s Guide
We replace failed CertainTeed flashing with manufacturer-compatible components, and most Sunrise Manor jobs run $385 to $650 installed depending on length, roof pitch, and how much surrounding material has to come up with it. Shorter headwall and sidewall runs sit at the low end; chimney surrounds, skylight curbs, and valley transitions push toward the top. A crew can usually get through a single-run flashing replacement in one visit.

Owners rarely go looking for flashing. It finds them. You spot a brown ring creeping across a bedroom ceiling after a winter storm, or a rust-colored stain along the fascia you never noticed before. Then the roofer gets up there and points to a piece of metal that has quietly been failing for three seasons. In Sunrise Manor, that story is almost always tied to sun, wind-blown dust, and the way our summer heat cycles metal and sealant day after day.
Which CertainTeed Models This Applies To
CertainTeed flashing shows up across a wide span of their product lines, and the right replacement part depends on which line you’re actually working with. Their shingle families (Landmark, XT 25, Presidential, and Carriage House) each have specific profile thicknesses, and thicker architectural shingles need taller, wider flashing legs to sit properly against the roof. Their underlayment systems and accessory lines carry their own matching flashings. If you’re not sure what’s on your roof, check the shingle wrapper if you kept it, look for a manufacturer label in the attic near the roof deck, or measure the exposed shingle thickness and tab pattern. That measurement will tell a supplier which part to match.
On the OEM-versus-aftermarket question, we lean practical: CertainTeed’s own flashing is the guaranteed match when the part is available, and we order it that way when the job calls for exact spec. Quality aftermarket flashings from established metal manufacturers also perform well when you match the gauge, the profile, and the base metal correctly. Thin bargain flashing? That’s a false economy. It fails sooner, and it fails during the rain, not on a sunny Tuesday. We’re an authorized installer of CertainTeed products and also handle GAF and Owens Corning roofs, so we match the flashing to the system you already have rather than forcing one brand onto another. Ridgeline Roofing Co. is an independent contractor and is not affiliated with CertainTeed.
Styles & brands we work with
- Architectural shingles
- Metal roofing
- Tile roofing
- GAF
- Owens Corning
- Flat & low-slope
Signs Your CertainTeed Flashing Replacement Is Failing
Flashing fails before shingles do in most Sunrise Manor homes, and the signs are usually quiet at first:
- Water stains on the ceiling or top of a wall after storms. Water is getting past a flashing seam or behind the step flashing. If the stain appears only after wind-driven rain, the flashing is the leading suspect, not the field shingles.
- Rust, pitting, or chalky white corrosion on the metal. Our desert sun and wind-blown grit wear away the protective coating on flashing faster than most homeowners expect. Once the coating is gone, the metal starts to pit and hold water at the seams.
- Lifted, curled, or separated flashing edges. Sealant used to hold the edge down has dried and shrunk. On a pitched roof in Sunrise Manor, that lifted edge catches wind and pulls back further with every storm.
- Gaps or daylight visible at the wall roof junction. Step flashing that has pulled away from the wall leaves a direct path for water. If you can see daylight from inside the attic at that junction, the flashing is no longer doing its job.
- Granules and sealant debris in the gutter below a flashing run. That debris means the shingles and sealant around the flashing have broken down and are shedding material. It’s the early warning most owners miss until water is already inside.
See the difference
Before
After
Before
After
Before
AfterReplacement Cost & What’s Included
Flashing replacement pricing in Sunrise Manor depends on three things: how long the run is, how complex the junction is (a straight sidewall is simple; a chimney with a cricket is not), and whether surrounding shingles must be lifted and reset. Straight sidewall and headwall runs generally land in the $385 to $485 range. Chimney surrounds, skylight curbs, and valley transitions run $485 to $650.
Every quote is broken down line by line: the flashing material, the sealants and fasteners, the labor to lift and reset the surrounding shingles, and the clean-up. The number on the estimate is the number on the invoice, provided nothing hidden surfaces once the shingles come up (more on that below). All work carries our written 90-Day Done Right Promise: if it isn’t right, we come back and make it right, no arguing and no paperwork runaround.

If we open up the area and find rotted decking or failed underlayment under the flashing, we don’t just button it back up and hand you a bill. We stop, show you photos taken from your actual roof, explain the added scope, and give you a written line-item update before any work continues.
DIY or Call Us?
You can safely get on a ladder and look at flashing from the gutter line: check for rust, lifted edges, visible gaps, or stains on the fascia and soffit below. You can also check inside the attic for daylight at the wall-roof junction or water staining on rafters. That kind of inspection is genuinely useful and costs nothing.
Resealing a flashing edge is where we’d ask you to stop and call. Roofing sealant has to be applied to clean, dry metal at the right temperature, and our summer heat here in Sunrise Manor makes roofs slippery and sealants cure unpredictably. A homeowner who seals a lifted flashing edge on a 110-degree afternoon often creates a worse leak than the one they were trying to solve, and getting up on a pitched roof in that heat is the part we’d rather you didn’t do. Our technicians have up to 10 years of experience with flashing replacement on tile, shingle, and metal roofs, and they document every inspection with photos. Call (844) 941-3509 to schedule a free estimate.
FAQs
Most metal flashing lasts 15 to 25 years in sunny climates, but in Sunrise Manor’s heat and wind-driven dust, expect the lower end of that range unless the flashing was properly coated and installed. UV breaks down the sealant at the seams long before the metal itself fails, and that’s usually what causes the first leak. If the flashing is 15 years old or more, have it inspected even if you haven’t seen a leak yet. Call (844) 941-3509 and we’ll look at it.
Sometimes, yes. A single lifted edge with clean metal underneath can be resealed and re-fastened, and that’s a repair, not a replacement. But once the metal is pitted, the coating is gone, or the flashing has separated from the wall, replacement is the correct call. Patching corroded flashing is a temporary fix that fails in the first hard rain, and it usually costs more in the long run than replacing it once. We’ll tell you honestly which category your flashing falls into during the free inspection.
A single straight flashing run is usually finished in two to four hours, including lifting and resetting the surrounding shingles. Chimney, skylight, or valley work takes longer, typically half a day to a full day, because the junctions are more involved. Most Sunrise Manor jobs are done in a single visit.
We match the part to your shingle thickness, roof pitch, and the specific junction type, then order through established flashing manufacturers who supply CertainTeed-compatible profiles. We don’t carry parts on a truck or keep local stock; every part is ordered to fit your actual roof once our technician has measured it on site. That’s how we avoid the wrong-gauge, wrong-width mismatch that causes most repeat leaks. Call (844) 941-3509 to schedule the inspection and get a written quote before we order a thing.
Written by the team at Ridgeline Roofing Co. Sunrise Manor, serving Sunrise Manor and nearby areas.